phenem wrote:What do you mean by this? Do you mean there is a 5-10% error margin because of the drive by wire? Basically I just want to know that I can adjust it from the stock form to allow it to open more,

throttle can't open more than 85-90% phisically

phenem wrote:as well as the 1st and 2nd gear boost maps.

this map is available

what about 3rd gear boost map? AFAIK in Speed3/3MPS the boost is not full on 3rd gear too?

misiekwaw wrote:what about 3rd gear boost map? AFAIK in Speed3/3MPS the boost is not full on 3rd gear too?

All needed maps are available: gear boost correction, max load for each gear

Hello Epifan...

I have some questions and I hope you can answer.

1: Do you have definitions for Australian 2008 CX7..??

2: How safe is MazdaEdit? Is it possible to break ECU..??

3: Personal version can write to only one ECU. Can it read more than one ECU?

4: Do you have information on what all maps mean..?? Scaling and Axis..??

5: What is the best operating system to use? Will MazdaEdit run on Windows 7 (64bit) and WinXP..??

Thank you..!!!

sassimac wrote:1: Do you have definitions for Australian 2008 CX7..??

not yet. But this is not a problem. I need about 1hour to create XML for a new car.

sassimac wrote:2: How safe is MazdaEdit? Is it possible to break ECU..??

mazdaEdit uses Mazda firmware update protocol. I didn't know about incidents of unsuccesful flashing. Flash process is restartable.

sassimac wrote:3: Personal version can write to only one ECU. Can it read more than one ECU?

No

sassimac wrote:4: Do you have information on what all maps mean..?? Scaling and Axis..??

Yes

sassimac wrote:5: What is the best operating system to use? Will MazdaEdit run on Windows 7 (64bit) and WinXP..??

It works on W7 64bit and other old OS including WinXP.

This strikes me as some impressive software.

I have actually become aware, lately, of professional tuners using this software, and figure if they are, why shouldnt I.

Do you have a release date for 2010 MPS/mazdaspeed 2.3T models?

I am from Australia and am aware of variations in ECU programing between US models in the 1st gen MPS, compared to Aus versions. When you release this for Gen 2 MPS's will you be able to factor in those differences, if there are any?

I suppose, more to the point, would those variations in programming make any difference in the functionality of your software?

Thank you for your time.

LittleredMPS wrote:This strikes me as some impressive software.

Do you have a release date for 2010 2.3T models?

+1. Any update on the development for the second generation of the 2.3L (2010+) models?

Will this software work on the N/A 2.3 models as well or could you build something for it?

I'm looking for a new tuning solution for our 2.3 Duratec powered Mazda3 rally car.

Any help would be greatly appreciated.

Thanks.

Rally711 wrote:Will this software work on the N/A 2.3 models as well or could you build something for it?

I'm looking for a new tuning solution for our 2.3 Duratec powered Mazda3 rally car.

Any help would be greatly appreciated.

Thanks.

Yes, It worx Perfectly. I have done on DBW 2.3 Duratec N/A Mazda6. As result, 11whp increase on CAI and High Flow Exhaust system. Gud Luck!

So how much will it cost me, and how long will it take to ship to the Western US? It would be nice to have the upgraded version since I work on other Mazdas as well.

We are in the process of building a new block, and I'd like to have the software, and be able to use it asap.

Thanks.

Currently, Personal Version didn't support N/A models.
Pro version do this.

Rally711 wrote:So how much will it cost me, and how long will it take to ship to the Western US? It would be nice to have the upgraded version since I work on other Mazdas as well.

We are in the process of building a new block, and I'd like to have the software, and be able to use it asap.

Thanks.

a new version of mazdaedit personal version is it out?
I have V 1.1 and got a few crashes and the dyno does not work.

Fracass
PM sent

Will this work with the 2010 AWD CX-7 2.3l Turbo US Model?

epifan wrote:Fracass
PM sent

Thank you, the new version works very well.