For logger STI 08, 09 EUDM - AZ1G202G and AZ1G201G

For logger STI 08, 09 EUDM - AZ1G202G and AZ1G201G

Postby Legaulois » Thu May 06, 2010 9:13 am

Additional definitions

Cruise/NoCruise : FFFF8A5E
Switch-Intel3-Sport1-Sport#2 : FFFF611D
RPM - #FF6810 - float - tr/mn
Engine Load - #FF65D4 - float
Véhicule Speed - FFFF67E8 - float - km/h
RPM 2 - FFFF79C8 - float - tr/mn
battery - FFFF412C - float - Volt
Fine Cruise/NoCruise - FFFF6658 - float
Gear - FFFF69FC
Atmospheric Pressure - FFFF6A6C - float - *.001333224 - Bar
Calculated Base Pulse With - FFFF6F1C - float - *.001 - ms
Coolant Température - FFFF6540 - Float - C
Vehicle Stop/roll - FFFF85CC - on/off
Memory Start Coolant temperature - FFFF6544 - Float - °C
Min RPM Start Engine - FFFF8338 - float - rpm
Throttle Motor Duty - FFFF8758 - float - %
A/F Sensor 1 Current - FFFF40DC - float - mA
Mass Air Flow - FFFF65B0 - float - g/s
Vehicule Speed 2 - FFFF67EC - float - Kph
Ignition Total Timing - FFFF79C1 - float - Degree
Intake Air Temperature - FFFF6A70 - float - C
Mass Air Flow 2 - FFFF65AC - float - g/s
Rear O2 Sensor - FFFF43F8 - float - Volt
Primary Wastegate Duty Cycle - FFFF5EDC -float - ms
Atmospheric Pressure - FFFF6A70 - float - /750 - Bar
Fuel Pump Duty - FFFF7DA4 - float - %
Tumble Valve Position Sensor - FFFF4028 - uint8 - /50
CPC Valve Duty Ratio - FFFF6B78 - float - % - *100
Mass Air Flow - FFFF65AC - float - g/s
Intake VVT Advance Angle Right - FFFF8B08 - float - degree
Intake VVT Advance Angle Left - FFFF8B0C - float - degree
Intake OCV Duty Right - FFFF8B60 - float - %
Intake OCV Duty Left - FFFF8B64 - float - %
Intake OCV Current Right - FFFF6610 - float - mA
Intake OCV Current Left - FFFF661C - float - mA
Neutral Position Switch - FFFF679B - 8 Bits - On/Off
Air Conditioning Switch - FFFF679F - 8 Bits - On/Off
Idle Switch - FFFF8023 - 8 Bits - On/Off
Ignition Switch - FFFF6798 - 8 Bits - On/Off
Accelerator Switch - FFFF6144 - 8 Bits - On/Off
Radiator Fan Relay #1 Switch - FFFF8816 - uint8 - On/Off
Radiator Fan Relay #2 Switch - FFFF8817 - uint8 - On/Off
Current Gear - FFFF69FE - uint8 - (1, 2, 3, 4, 5)
Per Gear Ingetion Timing Compensation Active - FFFF7B48 - unit8 - on/off

Tables supplémentaires :
"Fuel Pump Duty"
Code: Select all
<map name="Fuel Pump Duty" type="2" help="The Ecu will set fuel pump duty cycle to 0%, 100 %, or one of there two values" class="Fueling - Pump">
   <data offset="#43450" storagetype="float" metric="%" caption="Pump %"/>
   <rows count="2">
      <value>Medium</value>
      <value>Low</value>
   </rows>
</map>


"Ignition Dwell"
Code: Select all
<map name="Ignition Dwell" type="3" help="Ce tableau définit le délai avant l'étincelle que l'ecu doit mettre avant de démarrer le système d'allumage. Le temps nécessaire pour charger l'ecu jusqu'à l'explosion varie selon la vitesse du moteur, vous devez donc démarrer cet événement plus tôt pour compenser le déplacement rapide du piston." class="Ignition experimental">
   <rows count="5" offset="#D462C" storagetype="float" format="%.0f" metric="Volts" caption="Battery"/>
   <cols count="16" offset="#D45EC" storagetype="float" format="%.0f" metric="RPM" caption="Engine Speed"/>
   <data offset="#D4640" storagetype="uint16" func_2val="[value]*.004" func_val2="[value]/.004" metric="ms" caption="Ignition Dwell"/>
</map>


"Timing Compensation per Gear"
Code: Select all
        </map>    <map name=\"Timing Compensation per Gear 1st\" type=\"3\" class=\"Ignition Timing - Compensation\">
            <rows count=\"3\" offset=\"#D0E4C\" storagetype=\"float\" format=\"%.0f\" metric=\"rpm\" caption=\"Engine Speed\"/>
            <cols count=\"4\" offset=\"#D0E3C\" storagetype=\"float\" metric=\"g/rev\" caption=\"Engine Load\"/>
            <data offset=\"#D0E58\" metric=\"Ignition Timing Correction (degrees)\"/>
        </map>
        <map name=\"Timing Compensation per Gear 2nd\" type=\"3\" class=\"Ignition Timing - Compensation\">
            <rows count=\"3\" offset=\"#D0E74\" storagetype=\"float\" format=\"%.0f\" metric=\"rpm\" caption=\"Engine Speed\"/>
            <cols count=\"4\" offset=\"#D0E64\" storagetype=\"float\" metric=\"g/rev\" caption=\"Engine Load\"/>
            <data offset=\"#D0E80\" metric=\"Ignition Timing Correction (degrees)\"/>
        </map>
        <map name=\"Timing Compensation per Gear 3rd\" type=\"3\" class=\"Ignition Timing - Compensation\">
            <rows count=\"3\" offset=\"#D0E9C\" storagetype=\"float\" format=\"%.0f\" metric=\"rpm\" caption=\"Engine Speed\"/>
            <cols count=\"4\" offset=\"#D0E8C\" storagetype=\"float\" metric=\"g/rev\" caption=\"Engine Load\"/>
            <data offset=\"#D0EA8\" metric=\"Ignition Timing Correction (degrees)\"/>
        </map>
        <map name=\"Timing Compensation per Gear 4th\" type=\"3\" class=\"Ignition Timing - Compensation\">
            <rows count=\"3\" offset=\"#D0EC4\" storagetype=\"float\" format=\"%.0f\" metric=\"rpm\" caption=\"Engine Speed\"/>
            <cols count=\"4\" offset=\"#D0EB4\" storagetype=\"float\" metric=\"g/rev\" caption=\"Engine Load\"/>
            <data offset=\"#D0ED0\" metric=\"Ignition Timing Correction (degrees)\"/>
        </map>
        <map name=\"Timing Compensation per Gear 5th\" type=\"3\" class=\"Ignition Timing - Compensation\">
            <rows count=\"3\" offset=\"#D0EEC\" storagetype=\"float\" format=\"%.0f\" metric=\"rpm\" caption=\"Engine Speed\"/>
            <cols count=\"4\" offset=\"#D0EDC\" storagetype=\"float\" metric=\"g/rev\" caption=\"Engine Load\"/>
            <data offset=\"#D0EF8\" metric=\"Ignition Timing Correction (degrees)\"/>
        </map>
       
        <map name=\"Timing Compensation Per Gear RPM\" type=\"2\" class=\"Ignition Timing - Compensation\">
            <rows count=\"2\">
                <value>Enable Above</value>
                <value>Disable Below</value>
            </rows>
            <data offset=\"#CE2C0\" storagetype=\"float\" format=\"%.0f\" metric=\"rpm\" caption=\"Engine speed\"/>
        </map>
        <map name=\"Timing Compensation Per Gear Load\" type=\"2\" class=\"Ignition Timing - Compensation\">
            <rows count=\"2\">
                <value>Enable Above</value>
                <value>Disable Below</value>
            </rows>
            <data offset=\"#CE2C8\" storagetype=\"float\" metric=\"g/rev\" caption=\"Engine load\"/>
        </map>
        <map name=\"Timing Compensation Per Gear Result Conversion Multiplier\" type=\"2\" class=\"Ignition Timing - Compensation\">
            <data offset=\"#CE2D0\" storagetype=\"float\" caption=\"Timing Compensation\"/>
            <rows>
                <value>Multiplier</value>
            </rows>
        </map>
Last edited by Legaulois on Fri Oct 01, 2010 9:30 am, edited 8 times in total.
Legaulois
 
Posts: 63
Joined: Thu Jul 03, 2008 2:24 pm
Location: Nice - France

Re: For logger STI 08, 09 EUDM - AZ1G202G and AZ1G201G

Postby Legaulois » Tue May 25, 2010 12:09 pm

Add

A/F Sensor 1 Current - FFFF40DC - float - mA
Mass Air Flow - FFFF65B0 - float - g/s
Vehicule Speed 2 - FFFF67EC - float - Kph
Ignition Total Timing - FFFF79C1 - float - Degree
Intake Air Temperature - FFFF6A70 - float - C
Mass Air Flow 2 - FFFF65AC - float - g/s
Rear O2 Sensor - FFFF43F8 - float - Volt
Primary Wastegate Duty Cycle - FFFF5EDC -float - ms
Atmospheric Pressure - FFFF6A70 - float - /750 - Bar
Fuel Pump Duty - FFFF7DA4 - float - %
Tumble Valve Position Sensor - FFFF4028 - uint8 - /50
CPC Valve Duty Ratio - FFFF6B78 - float - % - *100
Mass Air Flow - FFFF65AC - float - g/s
Intake VVT Advance Angle Right - FFFF8B08 - float - degree
Intake VVT Advance Angle Left - FFFF8B0C - float - degree
Intake OCV Duty Right - FFFF8B60 - float - %
Intake OCV Duty Left - FFFF8B64 - float - %
Intake OCV Current Right - FFFF6610 - float - mA
Intake OCV Current Left - FFFF661C - float - mA
Legaulois
 
Posts: 63
Joined: Thu Jul 03, 2008 2:24 pm
Location: Nice - France

Re: For logger STI 08, 09 EUDM - AZ1G202G and AZ1G201G

Postby Legaulois » Mon Jun 28, 2010 1:36 pm

Add

Neutral Position Switch - FFFF679B - 8 Bits - On/Off
Air Conditioning Switch - FFFF679F - 8 Bits - On/Off
Idle Switch - FFFF8023 - 8 Bits - On/Off
Ignition Switch - FFFF6798 - 8 Bits - On/Off
Accelerator Switch - FFFF6144 - 8 Bits - On/Off
Radiator Fan Relay #1 Switch - FFFF8816 - uint8 - On/Off
Radiator Fan Relay #2 Switch - FFFF8817 - uint8 - On/Off
Legaulois
 
Posts: 63
Joined: Thu Jul 03, 2008 2:24 pm
Location: Nice - France

Re: For logger STI 08, 09 EUDM - AZ1G202G and AZ1G201G

Postby Legaulois » Fri Oct 01, 2010 9:29 am

add

Current Gear - FFFF69FE - uint8 - (1, 2, 3, 4, 5)
Per Gear Ingetion Timing Compensation Active - FFFF7B48 - unit8 - on/off

Tables supplémentaires :
"Fuel Pump Duty"
Code: Select all
<map name="Fuel Pump Duty" type="2" help="The Ecu will set fuel pump duty cycle to 0%, 100 %, or one of there two values" class="Fueling - Pump">
   <data offset="#43450" storagetype="float" metric="%" caption="Pump %"/>
   <rows count="2">
      <value>Medium</value>
      <value>Low</value>
   </rows>
</map>


"Ignition Dwell"
Code: Select all
<map name="Ignition Dwell" type="3" help="Ce tableau définit le délai avant l'étincelle que l'ecu doit mettre avant de démarrer le système d'allumage. Le temps nécessaire pour charger l'ecu jusqu'à l'explosion varie selon la vitesse du moteur, vous devez donc démarrer cet événement plus tôt pour compenser le déplacement rapide du piston." class="Ignition experimental">
   <rows count="5" offset="#D462C" storagetype="float" format="%.0f" metric="Volts" caption="Battery"/>
   <cols count="16" offset="#D45EC" storagetype="float" format="%.0f" metric="RPM" caption="Engine Speed"/>
   <data offset="#D4640" storagetype="uint16" func_2val="[value]*.004" func_val2="[value]/.004" metric="ms" caption="Ignition Dwell"/>
</map>


"Timing Compensation per Gear"
Code: Select all
        </map>    <map name=\"Timing Compensation per Gear 1st\" type=\"3\" class=\"Ignition Timing - Compensation\">
            <rows count=\"3\" offset=\"#D0E4C\" storagetype=\"float\" format=\"%.0f\" metric=\"rpm\" caption=\"Engine Speed\"/>
            <cols count=\"4\" offset=\"#D0E3C\" storagetype=\"float\" metric=\"g/rev\" caption=\"Engine Load\"/>
            <data offset=\"#D0E58\" metric=\"Ignition Timing Correction (degrees)\"/>
        </map>
        <map name=\"Timing Compensation per Gear 2nd\" type=\"3\" class=\"Ignition Timing - Compensation\">
            <rows count=\"3\" offset=\"#D0E74\" storagetype=\"float\" format=\"%.0f\" metric=\"rpm\" caption=\"Engine Speed\"/>
            <cols count=\"4\" offset=\"#D0E64\" storagetype=\"float\" metric=\"g/rev\" caption=\"Engine Load\"/>
            <data offset=\"#D0E80\" metric=\"Ignition Timing Correction (degrees)\"/>
        </map>
        <map name=\"Timing Compensation per Gear 3rd\" type=\"3\" class=\"Ignition Timing - Compensation\">
            <rows count=\"3\" offset=\"#D0E9C\" storagetype=\"float\" format=\"%.0f\" metric=\"rpm\" caption=\"Engine Speed\"/>
            <cols count=\"4\" offset=\"#D0E8C\" storagetype=\"float\" metric=\"g/rev\" caption=\"Engine Load\"/>
            <data offset=\"#D0EA8\" metric=\"Ignition Timing Correction (degrees)\"/>
        </map>
        <map name=\"Timing Compensation per Gear 4th\" type=\"3\" class=\"Ignition Timing - Compensation\">
            <rows count=\"3\" offset=\"#D0EC4\" storagetype=\"float\" format=\"%.0f\" metric=\"rpm\" caption=\"Engine Speed\"/>
            <cols count=\"4\" offset=\"#D0EB4\" storagetype=\"float\" metric=\"g/rev\" caption=\"Engine Load\"/>
            <data offset=\"#D0ED0\" metric=\"Ignition Timing Correction (degrees)\"/>
        </map>
        <map name=\"Timing Compensation per Gear 5th\" type=\"3\" class=\"Ignition Timing - Compensation\">
            <rows count=\"3\" offset=\"#D0EEC\" storagetype=\"float\" format=\"%.0f\" metric=\"rpm\" caption=\"Engine Speed\"/>
            <cols count=\"4\" offset=\"#D0EDC\" storagetype=\"float\" metric=\"g/rev\" caption=\"Engine Load\"/>
            <data offset=\"#D0EF8\" metric=\"Ignition Timing Correction (degrees)\"/>
        </map>
       
        <map name=\"Timing Compensation Per Gear RPM\" type=\"2\" class=\"Ignition Timing - Compensation\">
            <rows count=\"2\">
                <value>Enable Above</value>
                <value>Disable Below</value>
            </rows>
            <data offset=\"#CE2C0\" storagetype=\"float\" format=\"%.0f\" metric=\"rpm\" caption=\"Engine speed\"/>
        </map>
        <map name=\"Timing Compensation Per Gear Load\" type=\"2\" class=\"Ignition Timing - Compensation\">
            <rows count=\"2\">
                <value>Enable Above</value>
                <value>Disable Below</value>
            </rows>
            <data offset=\"#CE2C8\" storagetype=\"float\" metric=\"g/rev\" caption=\"Engine load\"/>
        </map>
        <map name=\"Timing Compensation Per Gear Result Conversion Multiplier\" type=\"2\" class=\"Ignition Timing - Compensation\">
            <data offset=\"#CE2D0\" storagetype=\"float\" caption=\"Timing Compensation\"/>
            <rows>
                <value>Multiplier</value>
            </rows>
        </map>
Legaulois
 
Posts: 63
Joined: Thu Jul 03, 2008 2:24 pm
Location: Nice - France


Return to Logging and Analisis

Who is online

Users browsing this forum: No registered users and 1 guest

cron